DIY Blue / White 84 * 48 Nokia 5110 LCD Display Screen Module Module for Arduino

Description

Visit store
Items for sale
About us
Product Details
Specification:
1. "LIGHT" linked with GND, the backlight to be lit.
2. Need you to compress the screen and PCB tighter, might got loose after the delivery.
3 Use a 3.3V controller, otherwise the display could be quite vague.
LCD5110 Module:
Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested
Data interface level:2.7-5V
Backlight power supply voltage:highest 3.3V
Installation diameter:2mm
Backlight:White
Document for Download:Data
1．RST--------- reset
2．CE------------chip selection
3．DC-----------data/commands choice
4．DIN-----------serial data line
5．CLK------------serial Clock Speed
6．3.3V------------VCC
7．LIGHT--------- backlight control terminal
8．GND-----------power negative
Features:
84 X 48 dot matrix LCD,can show 4 lines of characters
Use serial interface communicate with the master processor,the number of interface signal line reduced
greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,
MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting
time.
Can use the conductive glue to connect the module with the printed board,without connecting cable.The
metal hooks on the module can fix the module on the printed board,which is very easy to install and
replace.
LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small
Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode.
Blue Backlights                                                                      White Backlights
Bare Screen(NO PCB)
Controller Philp PCD8544 LCD controller .
input voltage :2.7-3.3v
can be driverd by Arduino/STM32/8051/AVR/PIC and other low power controllers
Compatible with Nokia 3310 LCD driving source code
NOTE:This item is only Nokia 5100 LCD bare screen without PCB pinboard
Package Included:
1*Nokia 5110 LCD Bare Screen 84*48 (NO PCB) for Arduino AVR PIC STM32
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.