[4 pc] dsPIC30F6010A-30I/PF Digital Signal processing DSP PIC microcontroller i

Description

Original Electronic Components
dsPIC30F6010A-30-I/PF
Lot size: 4
Case: TQFP80 14x14x1 mm
Motor Control 16-bit Digital Signal Controller / Microcontroller
30MIPS 144K Code 8K RAM
Genuine components from USA; No China parts!
dsPIC30F Motor Control 16-bit Digital Signal Controller. Seamless migration options from this device to dsPIC33F and PIC24 devices in similar packages.
Parameter Name Value
Architecture 16-bit
CPU Speed (MIPS) 30
Memory Type Flash
Program Memory (KB) 144
RAM Bytes 8,192
Temperature Range C -40 to 125
Operating Voltage Range (V) 2.5 to 5.5
I/O Pins 68
Pin Count 80
System Management Features PBOR, LVD
POR Yes
WDT Yes
Internal Oscillator 7.37 MHz, 512 kHz
nanoWatt Features Fast Wake/Fast Control
Digital Communication Peripherals 2-UART, 2-SPI, 1-I2C
Codec Interface No
Analog Peripherals 1-A/D 16x10-bit @ 1000(ksps)
Comparators 0
CAN (#, type) 2 CAN
Capture/Compare/PWM Peripherals 8/8
Motor Control PWM Channels 8
Quadrature Encoder Interface (QEI) 1
Timers 5 x 16-bit 2 x 32-bit
Parallel Port GPIO
Hardware RTCC No
DMA 0
Features
High-Performance Modified RISC CPU:
# Modified Harvard architecture
# C compiler optimized instruction set architecture
# 84 base instructions with flexible addressing modes
# 24-bit wide instructions, 16-bit wide data path
# 16 x 16-bit working register array
# Up to 30 MIPs operation: - DC to 40 MHz external clock input - 4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)
# Peripheral and External interrupt sources
# 8 user selectable priority levels for each interrupt
# 4 processor exceptions and software traps
# Primary and Alternate interrupt Vector Tables DSP Engine Features:
# Modulo and Bit-Reversed Addressing modes
# Two, 40-bit wide accumulators with optional saturation logic
# 17-bit x 17-bit single cycle hardware fractional/ integer multiplier
# Single cycle Multiply-Accumulate (MAC) operation
# 40-stage Barrel Shifter
# Dual data fetch Peripheral Features:
# High current sink/source I/O pins: 25 mA/25 mA
# Optionally pair up 16-bit timers into 32-bit timer modules
# 3-wire SPI� modules (supports 4 Frame modes)
# I2C� module supports Multi-Master/Slave mode and 7-bit/10-bit addressing
# Addressable UART modules with FIFO buffers Motor Control PWM Module Features:
# Complementary or Independent Output modes
# Edge and Center Aligned modes
# Multiple duty cycle generators
# Dedicated time base with 4 modes
# Programmable output polarity
# Dead time control for Complementary mode
# Manual output control
# Trigger for synchronized A/D conversions Quadrature Encoder Interface Module Features:
# Phase A, Phase B and Index Pulse input
# 16-bit up/down position counter
# Count direction status
# Position Measurement (x2 and x4) mode
# Programmable digital noise filters on inputs
# Alternate 16-bit Timer/Counter mode
# Interrupt on position counter rollover/underflow Analog Features:
# 10-bit 1 Msps Analog-to-Digital Converter (A/D)
# A/D Conversion available during Sleep and Idle
# 4 Sample/Hold Channels
# Multiple Conversion Sequencing Options Special Microcontroller Features:
# Enhanced Flash program memory: - 10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)
# Data EEPROM memory: - 100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)
# Self-reprogrammable under software control
# Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
# Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliable operation
# Fail-Safe clock monitor operation
# Detects clock failure and switches to on-chip low power RC oscillator
# Programmable code protection
# In-Circuit Serial Programming� (ICSP�)
# Programmable Brown-out Detection and Reset generation
# Selectable Power Management modes - Sleep, Idle and Alternate Clock modes CMOS Technology:
# Low power, high speed Flash technology
# Wide operating voltage range (2.5V to 5.5V)
photo is for packege reference only, and may show different part number
Purchases can only be changed or cancelled before payment.
Delivery dates provided by eBay are not guaranteed. Transit time can be 5-7 business days in USA after 1-2 day processing, however USPS does not guarantee these times, and can exceed them. If you have any time constraints, please contact seller before bidding / buying, to discuss shipping arrangements and delivery dates.
PAYMENT CLOSES ORDER AND COMMITS IT FOR SHIPPING. Your shipping label is created and billed along with insurance the moment you click "PAY". Paypal and insurance charges are non-recoverable. No cancellation possible after payment.
Any returns not resulting from seller wrongdoing will be assessed a restocking fee of 18% and will forfeit shipping costs.
International transit times can reach 8 weeks, 10 weeks for Italy and Brazil. Contact seller for alternate shipping options if this is not acceptable to you.
RETURNS can only be made with parts that have not been soldered. Before using, buyer must test one part as per the test information in the manufacturer's data sheet. This test is easy for any engineer or technician. This product is aimed at the industrial market. It is not a consumer product.